LCD1602 Breadboard DuPont Cable RFID Starter Learning Kit For Arduino Raspberry Pi 3 Pi 2 Model B / B+
- $30.89
Features:
Arduino Starter Kit is equipped with a large number of electronic components and test code.
Arduino Getting Started Tutorial After repeated validation, be sure to use the beginner.
Package includes:
1 x RC522 RFID Module
1 x ID Card
1 x Special-shaped ID Card
1 x LCD1602
1 x PS2 Joystick Module
1 x Ultrasonic Distance Sensor Module
1 x Tria xial Accelerometer Sensor Module(ADxL345)
1 x DHT-11 (Digital Temperature & Humidity sensor)
1 x ADC0832
1 x Stepper Motor
1 x Stepper Motor Driver Module (Based on ULN2003A)
1 x L9110 motor driver
1 x DC Motor
1 x 4*4 Matrix Keyboard
1 x Breadboard Power Supply Module
1 x 40 pin GPIO E xtension Board
1 x 40 pin GPIO Cable
2 x Light Sensor (Photoresistor)
1 x Analog Temperature Sensor (Thermistor)
1 x Relay
1 x Active Buzzer
1 x Passive Buzzer
1 x 7-Segment Display
1 x 4-bit 7-segment Display
1 x LED Bar Graph Display
1 x Dot-matrix Display
2 x 74HC595
1 x Tilt Switch
2 x Switch
1 x RGB LED
8 x Red LED
4 x Green LED
4 x Yellow LED
4 x Blue LED
4 x Button (large)
5 x Button (small)
1 x Button cap (red)
1 x Button cap (white)
2 x Button cap (blue)
16 x Resistor (220Ω)
10 x Resistor (1kΩ)
5 x Resistor (10kΩ)
2 x Potentiometer (10KΩ)
5 x Capacitor (104)
2 x Capacitor (10uF)
2 x 1N4148 Diode
2 x 1N4001 Diode
4 x NPN Transistor (8050)
4 x PNP Transistor (8550)
1 x Breadboard
40 x Male to Male Jumper Wires
20 x Male to Female Jumper Wires
20 x Female to Female Jumper Wires
1 x Header (40pin)
1 x Band Resistor Card
1 x Project Box
Arduino Starter Kit is equipped with a large number of electronic components and test code.
Arduino Getting Started Tutorial After repeated validation, be sure to use the beginner.
Package includes:
1 x RC522 RFID Module
1 x ID Card
1 x Special-shaped ID Card
1 x LCD1602
1 x PS2 Joystick Module
1 x Ultrasonic Distance Sensor Module
1 x Tria xial Accelerometer Sensor Module(ADxL345)
1 x DHT-11 (Digital Temperature & Humidity sensor)
1 x ADC0832
1 x Stepper Motor
1 x Stepper Motor Driver Module (Based on ULN2003A)
1 x L9110 motor driver
1 x DC Motor
1 x 4*4 Matrix Keyboard
1 x Breadboard Power Supply Module
1 x 40 pin GPIO E xtension Board
1 x 40 pin GPIO Cable
2 x Light Sensor (Photoresistor)
1 x Analog Temperature Sensor (Thermistor)
1 x Relay
1 x Active Buzzer
1 x Passive Buzzer
1 x 7-Segment Display
1 x 4-bit 7-segment Display
1 x LED Bar Graph Display
1 x Dot-matrix Display
2 x 74HC595
1 x Tilt Switch
2 x Switch
1 x RGB LED
8 x Red LED
4 x Green LED
4 x Yellow LED
4 x Blue LED
4 x Button (large)
5 x Button (small)
1 x Button cap (red)
1 x Button cap (white)
2 x Button cap (blue)
16 x Resistor (220Ω)
10 x Resistor (1kΩ)
5 x Resistor (10kΩ)
2 x Potentiometer (10KΩ)
5 x Capacitor (104)
2 x Capacitor (10uF)
2 x 1N4148 Diode
2 x 1N4001 Diode
4 x NPN Transistor (8050)
4 x PNP Transistor (8550)
1 x Breadboard
40 x Male to Male Jumper Wires
20 x Male to Female Jumper Wires
20 x Female to Female Jumper Wires
1 x Header (40pin)
1 x Band Resistor Card
1 x Project Box
Reviews
There are no reviews for this product.
